! Completed (STOP): border# border# *Jan 30 17:10:33.295: %HA_EM-6-LOG: catchall: show privilege *Jan 30 17:10:33.305: %HA_EM-6-LOG: catchall: disable *Jan 30 17:10:33.316: %HA_EM-6-LOG: catchall: connect out *Jan 30 17:10:35.030: %SEC_LOGIN-5-LOGIN_SUCCESS: Login Success [user: dnac] [Source: 10.181.15.3] [localport: 22] at 17:10:35 UTC Sat Jan 30 2021 *Jan 30 17:10:35.046: %HA_EM-6-LOG: catchall: enable *Jan 30 17:10:35.053: %HA_EM-6-LOG: catchall: terminal length 0 *Jan 30 17:10:35.070: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:10:35.084: %HA_EM-6-LOG: catchall: show hosts *Jan 30 17:10:35.124: %HA_EM-6-LOG: catchall: show running-config *Jan 30 17:10:35.382: %HA_EM-6-LOG: catchall: show clock *Jan 30 17:10:35.433: %HA_EM-6-LOG: catchall: show cdp neighbors detail *Jan 30 17:10:35.495: %HA_EM-6-LOG: catchall: show snmp mib ifmib ifindex *Jan 30 17:10:35.551: %HA_EM-6-LOG: catchall: show module *Jan 30 17:10:35.763: %HA_EM-6-LOG: catchall: show interfaces *Jan 30 17:10:35.849: %HA_EM-6-LOG: catchall: show ip interface *Jan 30 17:10:35.912: %HA_EM-6-LOG: catchall: show etherchannel summary *Jan 30 17:10:36.018: %HA_EM-6-LOG: catchall: show interfaces switchport *Jan 30 17:10:36.457: %HA_EM-6-LOG: catchall: show version *Jan 30 17:10:36.510: %HA_EM-6-LOG: catchall: show vtp status *Jan 30 17:10:36.659: %HA_EM-6-LOG: catchall: show vlan *Jan 30 17:10:36.708: %HA_EM-6-LOG: catchall: show vlan mtu *Jan 30 17:10:37.315: %SYS-6-LOGOUT: User dnac has exited tty session 3(10.181.15.3) *Jan 30 17:10:44.937: %SEC_LOGIN-5-LOGIN_SUCCESS: Login Success [user: dnac] [Source: 10.181.15.3] [localport: 22] at 17:10:44 UTC Sat Jan 30 2021 *Jan 30 17:10:44.951: %HA_EM-6-LOG: catchall: enable *Jan 30 17:10:44.971: %HA_EM-6-LOG: catchall: terminal length 0 *Jan 30 17:10:44.989: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:10:45.005: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:10:45.018: %HA_EM-6-LOG: catchall: configure terminal *Jan 30 17:10:45.085: %HA_EM-6-LOG: catchall: event manager applet _L3Applet_GigabitEthernet1/0/2 authorization bypass *Jan 30 17:10:45.111: %HA_EM-6-LOG: catchall: event timer countdown time 1 *Jan 30 17:10:45.142: %HA_EM-6-LOG: catchall: action 1.0 cli command "enable" *Jan 30 17:10:45.175: %HA_EM-6-LOG: catchall: action 1.1 cli command "config t" *Jan 30 17:10:45.227: %HA_EM-6-LOG: catchall: action 1.2 cli command "interface GigabitEthernet1/0/2" *Jan 30 17:10:45.262: %HA_EM-6-LOG: catchall: action 1.3 cli command "no switchport" *Jan 30 17:10:45.315: %HA_EM-6-LOG: catchall: show running-config brief *Jan 30 17:10:45.495: %HA_EM-6-LOG: catchall: action 1.4 cli command "ip address 100.64.0.38 255.255.255.254" *Jan 30 17:10:45.537: %HA_EM-6-LOG: catchall: action 1.5 cli command "ip router isis" *Jan 30 17:10:45.259: %DMI-5-SYNC_NEEDED: Switch 1 R0/0: dmiauthd: Configuration change requiring running configuration sync detected - 'action 1.3 cli command "no switchport"'. The running configuration will be synchronized to the NETCONF running data store. *Jan 30 17:10:45.593: %HA_EM-6-LOG: catchall: action 1.6 cli command "isis network point-to-point" *Jan 30 17:10:45.625: %HA_EM-6-LOG: catchall: action 1.7 cli command "no shutdown" *Jan 30 17:10:45.685: %HA_EM-6-LOG: catchall: action 1.8 cli command "bfd interval 100 min_rx 100 multiplier 3" *Jan 30 17:10:45.721: %HA_EM-6-LOG: catchall: action 1.9 cli command "no ip redirects" *Jan 30 17:10:45.765: %HA_EM-6-LOG: catchall: action 2.0 cli command "dampening" *Jan 30 17:10:45.816: %HA_EM-6-LOG: catchall: action 2.1 cli command "logging event link-status" *Jan 30 17:10:45.856: %HA_EM-6-LOG: catchall: action 2.2 cli command "load-interval 30" *Jan 30 17:10:45.912: %HA_EM-6-LOG: catchall: action 2.3 cli command "description Fabric Physical Link" *Jan 30 17:10:45.936: %HA_EM-6-LOG: catchall: action 2.6 cli command "clns mtu 1400" *Jan 30 17:10:45.952: %HA_EM-6-LOG: catchall: action 2.7 cli command "exit" *Jan 30 17:10:46.043: %HA_EM-6-LOG: catchall: action 2.8 cli command "no event manager applet _L3Applet_GigabitEthernet1/0/2 authorization bypass" *Jan 30 17:10:46.097: %HA_EM-6-LOG: catchall: action 4.1 cli command "interface GigabitEthernet1/0/2" *Jan 30 17:10:46.133: %HA_EM-6-LOG: catchall: action 4.2 cli command "ip pim sparse-mode" *Jan 30 17:10:46.174: %HA_EM-6-LOG: catchall: action 4.4 cli command "do write memory" *Jan 30 17:10:46.199: %HA_EM-6-LOG: catchall: action 4.5 cli command "end" *Jan 30 17:10:46.232: %HA_EM-6-LOG: catchall: action 4.6 cli command "exit" *Jan 30 17:10:46.242: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:46.249: %SYS-5-CONFIG_I: Configured from console by dnac on vty1 (10.181.15.3) *Jan 30 17:10:46.253: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:47.085: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down *Jan 30 17:10:47.469: %BFDFSM-6-BFD_SESS_DOWN: BFD-SYSLOG: BFD session ld:2 handle:2,is going Down Reason: ECHO FAILURE *Jan 30 17:10:47.470: %CLNS-5-ADJCHANGE: ISIS: Adjacency to edge-5 (Vlan1) Down, bfd neighbor down *Jan 30 17:10:47.470: %CLNS-5-ADJCHANGE: ISIS: Adjacency to edge-5 (Vlan1) Down, bfd neighbor down *Jan 30 17:10:47.955: %BFD-6-BFD_IF_CONFIGURE: BFD-SYSLOG: bfd config apply, idb:GigabitEthernet1/0/2 *Jan 30 17:10:49.348: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:10:49.359: %HA_EM-6-LOG: catchall: configure terminal *Jan 30 17:10:49.421: %HA_EM-6-LOG: catchall: event manager applet _L3Applet_GigabitEthernet1/0/1 authorization bypass *Jan 30 17:10:49.435: %HA_EM-6-LOG: catchall: event timer countdown time 1 *Jan 30 17:10:49.486: %HA_EM-6-LOG: catchall: action 1.0 cli command "enable" *Jan 30 17:10:49.498: %SYS-5-CONFIG_I: Configured from console by on vty2 (EEM:_L3Applet_GigabitEthernet1/0/2) *Jan 30 17:10:49.513: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down *Jan 30 17:10:49.524: %HA_EM-6-LOG: catchall: action 1.1 cli command "config t" *Jan 30 17:10:49.570: %HA_EM-6-LOG: catchall: action 1.2 cli command "interface GigabitEthernet1/0/1" *Jan 30 17:10:49.610: %HA_EM-6-LOG: catchall: action 1.3 cli command "no switchport" *Jan 30 17:10:49.671: %HA_EM-6-LOG: catchall: action 1.4 cli command "ip address 100.64.0.34 255.255.255.254" *Jan 30 17:10:49.708: %HA_EM-6-LOG: catchall: action 1.5 cli command "ip router isis" *Jan 30 17:10:49.758: %HA_EM-6-LOG: catchall: action 1.6 cli command "isis network point-to-point" *Jan 30 17:10:49.794: %HA_EM-6-LOG: catchall: action 1.7 cli command "no shutdown" *Jan 30 17:10:49.857: %HA_EM-6-LOG: catchall: action 1.8 cli command "bfd interval 100 min_rx 100 multiplier 3" *Jan 30 17:10:49.894: %HA_EM-6-LOG: catchall: action 1.9 cli command "no ip redirects" *Jan 30 17:10:49.933: %HA_EM-6-LOG: catchall: action 2.0 cli command "dampening" *Jan 30 17:10:49.978: %HA_EM-6-LOG: catchall: action 2.1 cli command "logging event link-status" *Jan 30 17:10:50.012: %HA_EM-6-LOG: catchall: action 2.2 cli command "load-interval 30" *Jan 30 17:10:50.067: %HA_EM-6-LOG: catchall: action 2.3 cli command "description Fabric Physical Link" *Jan 30 17:10:50.107: %HA_EM-6-LOG: catchall: action 2.6 cli command "clns mtu 1400" *Jan 30 17:10:50.140: %HA_EM-6-LOG: catchall: action 2.7 cli command "exit" *Jan 30 17:10:50.229: %HA_EM-6-LOG: catchall: action 2.8 cli command "no event manager applet _L3Applet_GigabitEthernet1/0/1 authorization bypass" *Jan 30 17:10:50.285: %HA_EM-6-LOG: catchall: action 4.1 cli command "interface GigabitEthernet1/0/1" *Jan 30 17:10:50.333: %HA_EM-6-LOG: catchall: action 4.2 cli command "ip pim sparse-mode" *Jan 30 17:10:50.365: %HA_EM-6-LOG: catchall: action 4.4 cli command "do write memory" *Jan 30 17:10:50.394: %HA_EM-6-LOG: catchall: action 4.5 cli command "end" *Jan 30 17:10:50.421: %HA_EM-6-LOG: catchall: action 4.6 cli command "exit" *Jan 30 17:10:50.428: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:50.434: %SYS-5-CONFIG_I: Configured from console by dnac on vty1 (10.181.15.3) *Jan 30 17:10:50.438: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:50.703: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 100.64.0.38 on interface GigabitEthernet1/0/2 *Jan 30 17:10:51.688: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down *Jan 30 17:10:51.992: %PIM-5-NBRCHG: neighbor 100.64.0.39 UP on interface GigabitEthernet1/0/2 *Jan 30 17:10:51.993: %PIM-5-DRCHG: DR change from neighbor 100.64.0.38 to 100.64.0.39 on interface GigabitEthernet1/0/2 *Jan 30 17:10:52.040: %CLNS-5-ADJCHANGE: ISIS: Adjacency to edge-4 (Vlan1) Down, bfd neighbor down *Jan 30 17:10:52.040: %CLNS-5-ADJCHANGE: ISIS: Adjacency to edge-4 (Vlan1) Down, bfd neighbor down *Jan 30 17:10:51.711: %DMI-5-SYNC_NEEDED: Switch 1 R0/0: dmiauthd: Configuration change requiring running configuration sync detected - 'no switchport '. The running configuration will be synchronized to the NETCONF running data store. *Jan 30 17:10:52.164: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up *Jan 30 17:10:52.166: %IFDAMP-5-UPDOWN: interface GigabitEthernet1/0/2 update CLNS Routing state to UP, interface is not suppressed *Jan 30 17:10:52.170: %IFDAMP-5-UPDOWN: interface GigabitEthernet1/0/2 update IP Routing state to UP, interface is not suppressed *Jan 30 17:10:52.996: %BFD-6-BFD_SESS_CREATED: BFD-SYSLOG: bfd_session_created, neigh 100.64.0.39 proc:ISIS, idb:GigabitEthernet1/0/2 handle:3 act *Jan 30 17:10:53.165: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up *Jan 30 17:10:53.684: %SYS-5-CONFIG_I: Configured from console by on vty2 (EEM:_L3Applet_GigabitEthernet1/0/1) *Jan 30 17:10:53.707: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down *Jan 30 17:10:53.715: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:10:53.722: %HA_EM-6-LOG: catchall: configure terminal *Jan 30 17:10:53.745: %HA_EM-6-LOG: catchall: interface Vlan1 *Jan 30 17:10:53.769: %BFD-6-BFD_SESS_DESTROYED: BFD-SYSLOG: bfd_session_destroyed, ld:1 neigh proc:ISIS, handle:1 active *Jan 30 17:10:53.772: %HA_EM-6-LOG: catchall: no ip router isis *Jan 30 17:10:53.780: %HA_EM-6-LOG: catchall: no clns mtu *Jan 30 17:10:53.801: %HA_EM-6-LOG: catchall: no ip address *Jan 30 17:10:53.810: %BFDFSM-6-BFD_SESS_UP: BFD-SYSLOG: BFD session ld:3 handle:3 is going UP *Jan 30 17:10:53.813: %CLNS-5-ADJCHANGE: ISIS: Adjacency to edge-5 (GigabitEthernet1/0/2) Up, new adjacency *Jan 30 17:10:53.839: %HA_EM-6-LOG: catchall: no bfd interval *Jan 30 17:10:53.850: %HA_EM-6-LOG: catchall: ip redirects *Jan 30 17:10:53.859: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:53.865: %SYS-5-CONFIG_I: Configured from console by dnac on vty1 (10.181.15.3) *Jan 30 17:10:53.870: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:53.983: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:10:53.997: %HA_EM-6-LOG: catchall: configure terminal *Jan 30 17:10:54.044: %HA_EM-6-LOG: catchall: no ip dhcp pool nw_orchestration_pool *Jan 30 17:10:54.654: %PIM-5-DRCHG: DR change from neighbor 0.0.0.0 to 100.64.0.34 on interface GigabitEthernet1/0/1 *Jan 30 17:10:55.640: %HA_EM-6-LOG: catchall: show running-config brief *Jan 30 17:10:55.615: %DMI-5-SYNC_COMPLETE: Switch 1 R0/0: dmiauthd: The running configuration has been synchronized to the NETCONF running data store. *Jan 30 17:10:56.086: %HA_EM-6-LOG: catchall: no ip dhcp excluded-address 100.64.0.1 *Jan 30 17:10:56.109: %HA_EM-6-LOG: catchall: no ip dhcp class ciscopnp *Jan 30 17:10:56.138: %HA_EM-6-LOG: catchall: do-exec write memory *Jan 30 17:10:56.139: %HA_EM-6-LOG: catchall: write memory *Jan 30 17:10:56.271: %PIM-5-NBRCHG: neighbor 100.64.0.35 UP on interface GigabitEthernet1/0/1 *Jan 30 17:10:56.272: %PIM-5-DRCHG: DR change from neighbor 100.64.0.34 to 100.64.0.35 on interface GigabitEthernet1/0/1 *Jan 30 17:10:56.452: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up *Jan 30 17:10:56.453: %IFDAMP-5-UPDOWN: interface GigabitEthernet1/0/1 update CLNS Routing state to UP, interface is not suppressed *Jan 30 17:10:56.456: %IFDAMP-5-UPDOWN: interface GigabitEthernet1/0/1 update IP Routing state to UP, interface is not suppressed *Jan 30 17:10:56.531: %SYS-5-CONFIG_I: Configured from console by dnac on vty1 (10.181.15.3) *Jan 30 17:10:56.535: %HA_EM-6-LOG: catchall: exit *Jan 30 17:10:57.451: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to up *Jan 30 17:10:58.128: %CLNS-5-ADJCHANGE: ISIS: Adjacency to edge-4 (GigabitEthernet1/0/1) Up, new adjacency *Jan 30 17:11:06.080: %DMI-5-SYNC_COMPLETE: Switch 1 R0/0: dmiauthd: The running configuration has been synchronized to the NETCONF running data store. *Jan 30 17:11:14.085: %HA_EM-6-LOG: catchall: show privilege *Jan 30 17:11:14.094: %HA_EM-6-LOG: catchall: disable *Jan 30 17:11:14.106: %HA_EM-6-LOG: catchall: connect out *Jan 30 17:11:15.800: %SEC_LOGIN-5-LOGIN_SUCCESS: Login Success [user: dnac] [Source: 10.181.15.3] [localport: 22] at 17:11:15 UTC Sat Jan 30 2021 *Jan 30 17:11:15.816: %HA_EM-6-LOG: catchall: enable *Jan 30 17:11:15.825: %HA_EM-6-LOG: catchall: terminal length 0 *Jan 30 17:11:15.841: %HA_EM-6-LOG: catchall: terminal width 0 *Jan 30 17:11:15.864: %HA_EM-6-LOG: catchall: show running-config *Jan 30 17:11:16.151: %HA_EM-6-LOG: catchall: show hosts *Jan 30 17:11:16.213: %HA_EM-6-LOG: catchall: show ip igmp snooping *Jan 30 17:11:16.255: %HA_EM-6-LOG: catchall: show ipv6 mld snooping *Jan 30 17:11:16.310: %HA_EM-6-LOG: catchall: show clock *Jan 30 17:11:16.379: %HA_EM-6-LOG: catchall: show cdp neighbors detail *Jan 30 17:11:16.419: %HA_EM-6-LOG: catchall: show snmp mib ifmib ifindex *Jan 30 17:11:16.471: %HA_EM-6-LOG: catchall: show module *Jan 30 17:11:16.719: %HA_EM-6-LOG: catchall: show interfaces *Jan 30 17:11:16.810: %HA_EM-6-LOG: catchall: show ip interface *Jan 30 17:11:16.882: %HA_EM-6-LOG: catchall: show etherchannel summary *Jan 30 17:11:16.984: %HA_EM-6-LOG: catchall: show interfaces switchport *Jan 30 17:11:17.402: %HA_EM-6-LOG: catchall: show version *Jan 30 17:11:17.475: %HA_EM-6-LOG: catchall: show vtp status *Jan 30 17:11:17.584: %HA_EM-6-LOG: catchall: show vlan *Jan 30 17:11:17.623: %HA_EM-6-LOG: catchall: show vlan mtu *Jan 30 17:11:18.105: %SYS-6-LOGOUT: User dnac has exited tty session 1(10.181.15.3) border# border#